石油勘探与开发 >

2021 , Vol. 48 >Issue 1: 148 - 155

DOI: https://doi.org/10.11698/PED.2021.01.13

油气田开发

非均质油藏聚合物驱提高采收率机理再认识

  • 卢祥国 ,
  • 曹豹 ,
  • 谢坤 ,
  • 曹伟佳 ,
  • 刘义刚 ,
  • 张云宝 ,
  • 王晓燕 ,
  • 张杰
展开
  • 1.东北石油大学提高油气采收率教育部重点实验室,黑龙江大庆 163318;
    2.中海石油（中国）有限公司天津分公司采油工艺研究所,天津 300450;
    3.中国石油大港油田公司采油工艺研究院,天津 300280
卢祥国（1960-）,男,重庆綦江人,博士,东北石油大学教授,主要从事提高采收率理论与技术方面的教学和科研工作。地址：黑龙江省大庆市高新技术开发区学府街99号,东北石油大学石油工程学院,邮政编码：163318。E-mail: luxiangg2003@yahoo.com.cn

收稿日期: 2020-02-11

  修回日期: 2020-12-05

  网络出版日期: 2021-01-19

基金资助

国家“十三五”油气重大专项课题（2016ZX05058-003-010）; 国家自然科学基金面上项目（51574086）; 中国博士后创新人才支持计划（BX20190065）

收起

EOR mechanisms of polymer flooding in a heterogeneous oil reservoir

  • LU Xiangguo ,
  • CAO Bao ,
  • XIE Kun ,
  • CAO Weijia ,
  • LIU Yigang ,
  • ZHANG Yunbao ,
  • WANG Xiaoyan ,
  • ZHANG Jie
Expand
  • 1. Key Laboratory of Enhanced Oil and Gas Recovery of Ministry of Education, Northeast Petroleum University, Daqing 163318, China;
    2. Oil Production Technology Research Institute of Tianjin Branch of CNOOC, Tianjin 300450, China;
    3. Oil Production Technology Research Institute of Dagang Oilfield of CNPC, Tianjin 300280, China

Received date: 2020-02-11

  Revised date: 2020-12-05

  Online published: 2021-01-19

Fold

摘要

以大庆、大港、长庆等油田的储集层岩石和流体为模拟对象,探讨了非均质油藏聚合物驱提高采收率的机理和技术途径,通过对比“等黏度”和“等浓度”条件下普通聚合物溶液、甘油、“片-网”结构聚合物溶液和非均相弱凝胶等的驱油效果,论证了聚合物类驱油剂黏度与驱油效果间的关系,提出了改善聚合物驱效果的方法。研究表明,聚合物在多孔介质内因滞留作用进而扩大注入水波及体积是聚合物驱提高采收率主要机理,而聚合物类驱油剂黏度与驱油效果不存在正相关性,具有“片-网”结构的聚合物虽然增黏能力较强,但与储集层岩石孔喉结构的配伍性较差,其可注入性和抗剪切性较差;非均相弱凝胶体系在多孔介质内具有较强的吸附、捕集作用,容易在储集层岩石孔隙内滞留,在高渗透层（区域）能够建立有效的渗流阻力,与具有“等黏度”或“等浓度”的聚合物溶液相比,扩大波及体积能力更强;长时间注入聚合物类驱油剂,势必会导致吸液剖面反转,大大降低聚合物驱开发效果,采用“高滞留”与“低滞留或不滞留”驱油剂交替注入,可进一步改善聚合物类驱油剂驱油效果。图5表4参29

关键词： 非均质油藏; 聚合物驱; 驱油效果; 提高采收率; 波及体积; 改善方法

本文引用格式

卢祥国 , 曹豹 , 谢坤 , 曹伟佳 , 刘义刚 , 张云宝 , 王晓燕 , 张杰 . 非均质油藏聚合物驱提高采收率机理再认识[J]. 石油勘探与开发, 2021 , 48(1) : 148 -155 . DOI: 10.11698/PED.2021.01.13

Abstract

Taking reservoir rocks and fluids of the Daqing, Dagang and Changqing oilfields as research objects, the EOR mechanisms and technical approach of polymer flooding were discussed. By comparing the displacement performances of ordinary polymer, glycerol, polymer in “sheet-net” structure and heterogeneous weak gel at the same viscosity and concentration, the relationship between the viscosity of polymer displacement agents and displacement performance was demonstrated, and the method of improving polymer flooding effect was worked out. The main mechanism of polymer flooding to increase oil recovery is the swept volume expansion of water injection due to polymer retention in porous media. The viscosity of polymer agents has no positive correlation with polymer flooding effect. Although polymer of “sheet-net” structure has strong capacity in increasing viscosity, it has poor compatibility with pore throat structure of reservoir rock, low injectivity and low shear resistance. Heterogeneous weak gel system has higher adsorption and capture capacity in porous media, which is easy to retain in porous media, and can effectively establish seepage resistance in high permeability layers (zones). Compared with polymer solutions with the same viscosity or concentration, it has stronger ability to expand swept volume. Long term injection of polymer flooding agents will inevitably lead to fluid entry profile reversal, and thus worsening of polymer flooding effect. Alternate injection of high retention and low or non-retention displacement agents can further improve the displacement effect of polymer flooding agents.

Key words： heterogeneous reservoir; polymer flooding; displacement performances; enhancement of oil recovery; swept volume; improvement method

参考文献

[1] 袁士义, 王强. 中国油田开发主体技术新进展与展望[J]. 石油勘探与开发, 2018, 45(4): 657-668.
YUAN Shiyi, WANG Qiang.New progress and prospect of oilfields development technologies in China[J]. Petroleum Exploration and Development, 2018, 45(4): 657-668.
[2] 孙龙德, 伍晓林, 周万富, 等. 大庆油田化学驱提高采收率技术[J]. 石油勘探与开发, 2018, 45(4): 636-645.
SUN Longde, WU Xiaolin, ZHOU Wanfu, et al.Technologies of enhancing oil recovery by chemical flooding in Daqing Oilfield, NE China[J]. Petroleum Exploration and Development, 2018, 45(4): 636-645.
[3] 廖广志, 王强, 王红庄, 等. 化学驱开发现状与前景展望[J]. 石油学报, 2017, 38(2): 196-207.
LIAO Guangzhi, WANG Qiang, WANG Hongzhuang, et al.Chemical flooding development status and prospect[J]. Acta Petrolei Sinica, 2017, 38(2): 196-207.
[4] 李道山, 周嘉玺, 倪方天, 等. 大港油田南部高温高盐油藏污水聚合物驱实验研究[J]. 大庆石油地质与开发, 2007, 26(4): 100-104.
LI Daoshan, ZHOU Jiaxi, NI Fangtian, et al.Research on sewage based polymer flooding for high temperature and high salinity oil reservoir in south Dagang Oilfield[J]. Petroleum Geology & Oilfield Development in Daqing, 2007, 26(4): 100-104.
[5] 林玉君, 刘斌, 谭颖, 等. 辽河油田锦16块东区聚合物驱油试验研究[J]. 油气采收率技术, 1996, 3(3): 42-46.
LIN Yujun, LIU Bin, TAN Ying, et al.Experimental study on polymer flooding in the east of Block Jin 16 in Liaohe Oilfield[J]. Petroleum Geology and Recovery Efficiency, 1996, 3(3): 42-46.
[6] 孙焕泉. 聚合物驱后井网调整与非均相复合驱先导试验方案及矿场应用: 以孤岛油田中一区Ng3单元为例[J]. 油气地质与采收率, 2014, 21(2): 1-4.
SUN Huanquan.Application of pilot test for well pattern adjusting heterogeneous combination flooding after polymer flooding: A case of Zhongyiqu Ng3 block, Gudao Oilfield[J]. Petroleum Geology and Recovery Efficiency, 2014, 21(2): 1-4.
[7] 罗文利, 韩冬, 韦莉, 等. 抗盐碱星形聚合物的合成和性能评价[J]. 石油勘探与开发, 2010, 37(4): 477-482.
LUO Wenli, HAN Dong, WEI Li, et al.Synthesis and property evaluation of a salt and alkali-resistant star-polymer[J]. Petroleum Exploration and Development, 2010, 37(4): 477-482.
[8] 敬加强, 安云朋, 孙娜娜, 等. 表面活性剂对部分水解聚丙烯酰胺溶液抗盐性的影响[J]. 高分子通报, 2015(5): 61-68.
JING Jiaqiang, AN Yunpeng, SUN Nana, et al.Salt resisitance of surfactants and anionic polyacrylamide combined system[J]. Polymer Bulletin, 2015(5): 61-68.
[9] 谢坤, 卢祥国, 姜维东, 等. 抗盐聚合物储层适应性及其作用机制[J]. 中国石油大学学报(自然科学版), 2017, 41(3): 144-153.
XIE Kun, LU Xiangguo, JIANG Weidong, et al.Reservoir adaptability and mechanism of salt-resistant polymer[J]. Journal of China University of Petroleum (Natural Science Edition), 2017, 41(3): 144-153.
[10] 周灿灿, 王拥军, 周凤鸣. 近源砂岩原生孔隙储集层岩石相控建模及其应用[J]. 石油勘探与开发, 2006, 33(5): 553-557.
ZHOU Cancan, WANG Yongjun, ZHOU Fengming.Modeling and application of the lithofacies controlled primary pore reservoir of proximal sandstone[J]. Petroleum Exploration and Development, 2006, 33(5): 553-557.
[11] 俞启泰. 注水油藏大尺度未波及剩余油的三大富集区[J]. 石油学报, 2000, 21(2): 45-50.
YU Qitai.Three major rich areas of “large scale” unswept remaining oil in water flooded bedded sandstone reservoirs[J]. Acta Petrolei Sinica, 2000, 21(2): 45-50.
[12] 沈平平, 袁士义, 邓宝荣, 等. 化学驱波及效率和驱替效率的影响因素研究[J]. 石油勘探与开发, 2004, 31(S1): 1-4.
SHEN Pingping, YUAN Shiyi, DENG Baorong, et al.Influence factors of oil displacement efficiency and sweep efficiency in chemical flooding[J]. Petroleum Exploration and Development, 2004, 31(S1): 1-4.
[13] SHEN Pingping, YUAN Shiyi, DENG Baorong, et al.Quantitative description of the effects of sweep efficiency and displacement efficiency during chemical flooding on a heterogeneous reservoir[J]. Petroleum Science, 2004, 1(3): 41-48.
[14] 刘哲宇, 李宜强, 冷润熙, 等. 孔隙结构对砾岩油藏聚表二元复合驱提高采收率的影响[J]. 石油勘探与开发, 2020, 47(1): 129-139.
LIU Zheyu, LI Yiqiang, LENG Runxi, et al.Effects of pore structure on surfactant/polymer flooding-based enhanced oil recovery in conglomerate reservoirs[J]. Petroleum Exploration and Development, 2020, 47(1): 129-139.
[15] XIE Kun, LU Xiangguo, PAN He, et al.Analysis of dynamic imbibition effect of surfactant in micro cracks in reservoir with high temperature and low permeability[J]. SPE Production & Operations, 2018, 33(3): 596-606.
[16] 朱友益, 侯庆锋, 简国庆, 等. 化学复合驱技术研究与应用现状及发展趋势[J]. 石油勘探与开发, 2013, 40(1): 90-96.
ZHU Youyi, HOU Qingfeng, JIAN Guoqing, et al.Current development and application of chemical combination flooding technique[J]. Petroleum Exploration and Development, 2013, 40(1): 90-96.
[17] 兰玉波, 杨清彦, 李斌会. 聚合物驱波及系数和驱油效率实验研究[J]. 石油学报, 2006, 27(1): 64-68.
LAN Yubo, YANG Qingyan, LI Binhui.Experimental research on sweep efficiency and oil-displacement efficiency of polymer flooding[J]. Acta Petrolei Sinica, 2006, 27(1): 64-68.
[18] 王敏杰, 田慧卿, 赵丹阳. 聚合物熔体微尺度剪切黏度测量方法与黏度模型[J]. 机械工程学报, 2012, 48(16): 21-29.
WANG Minjie, TIAN Huiqing, ZHAO Danyang.Micro-scale shear viscosity testing approach and viscosity model of polymer melts[J]. Journal of Mechanical Engineering, 2012, 48(16): 21-29.
[19] 徐斌, 王敏杰, 于同敏, 等. 微尺度效应下的聚合物熔体粘度理论及试验[J]. 机械工程学报, 2010, 46(19): 125-132.
XU Bin, WANG Minjie, YU Tongmin, et al.Theoretical and experimental approach of the viscosity of polymer melt under micro-scale effect[J]. Journal of Mechanical Engineering, 2010, 46(19): 125-132.
[20] 吴行才, 韩大匡, 卢祥国, 等. 微凝胶颗粒水分散液体系在多孔介质中的驱替机理[J]. 地球科学, 2017, 42(8): 1348-1355.
WU Xingcai, HAN Dakuang, LU Xiangguo, et al.Oil displacing mechanism of soft micro particle dispersion in porous media[J]. Earth Science, 2017, 42(8): 1348-1355.
[21] 冯茹森, 嵇薇, 郭拥军, 等. 疏水缔合聚合物重均分子量的测定[J]. 高分子学报, 2014(1): 150-155.
FENG Rusen, JI Wei, GUO Yongjun, et al.The determination of weight-average molecular weight of hydrophobically associated water- soluble polymers[J]. Acta Polymerica Sinica, 2014(1): 150-155.
[22] 朱怀江, 刘强, 沈平平, 等. 聚合物分子尺寸与油藏孔喉的配伍性[J]. 石油勘探与开发, 2006, 33(5): 609-613.
ZHU Huaijiang, LIU Qiang, SHEN Pingping, et al.Compatibility between polymer molecular size and pore throat in reservoirs[J]. Petroleum Exploration and Development, 2006, 33(5): 609-613.
[23] 罗健辉, 卜若颖, 朱怀江, 等. 梳形聚丙稀酰胺的特性及应用[J]. 石油学报, 2004, 25(2): 65-68, 73.
LUO Jianhui, BU Ruoying, ZHU Huaijiang, et al.Property and application of comb_shape polyacrylamide[J]. Acta Petrolei Sinica, 2004, 25(2): 65-68, 73.
[24] 程杰成, 沈兴海, 袁士义, 等. 新型梳形抗盐聚合物的流变性[J]. 高分子材料科学与工程, 2004, 20(4): 119-121.
CHENG Jiecheng, SHEN Xinghai, YUAN Shiyi, et al.Study on rheology of polyacrylamide copolymer used in enhanced oil recovery[J]. Polymeric Materials Science and Engineering, 2004, 20(4): 119-121.
[25] CAO W, XIE K, LU X, et al.Effect of profile-control oil-displacement agent on increasing oil recovery and its mechanism[J]. Fuel, 2019, 237(FEB.1): 1151-1160.
[26] XIE K, CAO B, LU X, et al.Matching between the diameter of the aggregates of hydrophobically associating polymers and reservoir pore-throat size during polymer flooding in an offshore oilfield[J]. Journal of Petroleum Science & Engineering, 2019, 177: 558-569.
[27] XIE K, LU X, LI Q, et al.Analysis of reservoir applicability of hydrophobically associating polymer[J]. SPE Journal. 2016, 21(1): 1-9.
[28] 牛丽伟, 卢祥国, 王晓燕, 等. 聚合物、聚表剂和Cr3+聚合物凝胶分子构型及其渗流特性差异[J]. 中国石油大学学报(自然科学版), 2014, 38(6): 186-191.
NIU Liwei, LU Xiangguo, WANG Xiaoyan, et al.Differences in molecular configuration and seepage properties among polymer, active polymer and Cr3+ polymer gel[J]. Journal of China University of Petroleum (Natural Science Edition), 2014, 38(6): 186-191.
[29] 刘进祥, 卢祥国, 刘敬发, 等. 交联聚合物溶液在岩心内成胶效果及机理[J]. 石油勘探与开发, 2013, 40(4): 474-480.
LIU Jinxiang, LU Xiangguo, LIU Jingfa, et al.Mechanism and gelling effects of linked polymer solution in the core[J]. Petroleum Exploration and Development, 2013, 40(4): 474-480.
Options
文章导航

/

〈 〉

版权所有：《石油勘探与开发》编辑部；《石油勘探与开发（英文）》编辑部
地址：北京市海淀区学院路20号，中国石油勘探开发研究院数据中心605室　

京ICP备15044687号    技术支持：北京玛格泰克科技发展有限公司